SnapShot
Member
Jeep & Mocha "Remembering Patches, always"
Posts: 699
Location: Finally free from the Republic of Kalifornia!
|
Post by SnapShot on Aug 30, 2014 17:13:43 GMT -5
Here's something I have found useful in helping keep my "special" brass separate from the rest of the population. I use an oil based paint pen and fill in the head stamping on brass I need to keep track of. It must be oil based paint or brass cleaning will remove it easily. When the paint is ALMOST DRY, just buff it on paper towels, flat on the bench. The head stamp stays filled in and the rest of the paint buffs off. There are a lot of colors available in these pens at Home Depot. The picture is not great but you can see the 44 Magnum brass head stamp is now BLACK. These cases are trimmed to 1.255" to accommodate the Hornady FTX bullets. Standard trim length is 1.275" and the majority of my 44 Magnum brass is trimmed to that length. The 45 Colt brass is for BLANKS and has an oversized flash hole at 0.140". I use these for X-ring Rubber Bullets and sure don't want these babies mixed in with my regular 45 Colt Brass. I used red paint to fill in the word "BLANK" on the head stamp. This is not a fail-safe method but really helps if this brass gets mixed in with regular brass.
|
|
bob
Member
I'm too old to be nice but never too old to learn!
Posts: 1,457
Location: Northern California
|
Post by bob on Aug 30, 2014 17:24:07 GMT -5
Good idea snapshot, I was trying to think of a way to keep neck sized seperate from full length/small based sized brass thanks. Now a question why trim 0.020" to accommodate that bullet?
|
|
SnapShot
Member
Jeep & Mocha "Remembering Patches, always"
Posts: 699
Location: Finally free from the Republic of Kalifornia!
|
Post by SnapShot on Aug 30, 2014 17:51:04 GMT -5
BOB ~ I spent 3 days trying to get anyone from Hordany to answer that very question. Finally gave up and just did it (they are the experts). I'm shooting this in a wheel gun and that case length can't make a difference. The exact wording from Hornady Manual #9 is: "CASE TRIM LENGTH: 1.255" The data below was developed with FTX bullets. Due to the longer ogive it is critical that cartridge case be trimmed to length specified." ~ SnapShot (Larry)
|
|
|
Post by hacker54 on Aug 30, 2014 23:43:53 GMT -5
Larry, Bob, I do believe this is to make sure they do not protrude from the cylinder of a revolver. Load a couple dummy rounds using the FTX in a case of regular length and check to see if they bind anywhere. Whether closing the cylinder or bind in the rotation of the cylinder. Also if in a lever gun if one had to cycle rounds out of the gun they might bind in ejecting of the roud being longer than normal.
|
|
SnapShot
Member
Jeep & Mocha "Remembering Patches, always"
Posts: 699
Location: Finally free from the Republic of Kalifornia!
|
Post by SnapShot on Aug 31, 2014 13:26:58 GMT -5
Gary ~ I thought of this with my wheel guns too. The clearance from the tip of the bullet to the end of the cylinder is not an issue on any of my revolvers. I find no interference of any kind. S&W Model 29 (Dirty Harry) = 0.109" S&W Model 629 Backpacker = 0.112" Ruger Super Red Hawk Alaskan = 0.154" Also, I find no problems at all with the feed on my semi-automatic Desert Eagle. I don't have a lever gun in 44 Magnum so can't check on that possibility. Additional information from Hornady says; "The shorter trim length also effects case capacity and the data listed for the FTX® should not be deviated from." As Grandpa used to say; "I looks like someone is pickin' the fly specs out of the pepper." ~ SnapShot
|
|